Model 2800 Remote Monitoring with Wireless Sensors

Built-in Power Failure, Sound Level, Temperature*.

Inputs 4 Wireless & 4 Hard Wired.

Outputs 1 Relay (manual or automatic control).

Notifications 8 Custom Voice Phone Calls.

Special Features Wireless Sensors.

Sensaphone Model 2800 (Sensaphone Introduces Wireless Sensors)

Now you can monitor critical conditions at remote locations without running wires. Introducing the new Sensaphone 2800 with Wireless Sensor Technology.

Based on proven Sensaphone remote monitoring methods, the 2800 adds the ability to read sensor status from wireless sensors. And not just simple on/off status, or open/closed conditions. The Sensaphone Wireless Technology includes full analog capability so real world values can be monitored, like actual temperatures, real tank levels and flow rates.

You can use up to four of the Sensaphone wireless sensors with the 2800. A variety of wireless sensors types are available to choose from, including ...

• Temperature
• Humidity
• Power Failure
• Motion Detector
• Water on Floor

In addition to the wireless sensors, there are also two Wireless Interface modules. These allow you to connect to existing equipment or sensors and transmit their status back to the Sensaphone 2800 wirelessly. There is a Dry Contact wireless module, and even a 4-20mA wireless module. The 4-20mA wireless module even provides battery backed 24 VDC loop power for your transducer.

Stick It Anywhere!

Most of the Sensaphone Wireless Sensors run on batteries for up to 3 years. You can literally, just stick a sensor to the wall and start monitoring right away. The Sensaphone 2800 will scan, find the sensor, self configure and do most of the work for you. All you need to do is to record a custom voice message and fill in a few parameters.

Self Diagnostics

The Wireless Sensor Network is always being watched by the Sensaphone 2800. In addition to looking for alarms from the sensor values, it is also looking to make sure that each wireless sensor is fully functional and its batteries are full. If there are any problems with the wireless sensors, the 2800 will initiate a diagnostic alarm and notify the appropriate personnel immediately.

FEATURES

Also included on the Sensaphone 2800 are four traditional, hard-wired sensor inputs. These are Sensaphone Universal Inputs that can be used with temperature sensors, dry contact sensors, and even 4-20mA transducers. So, when you have monitoring requirements near the Sensaphone 2800, just wire them in. When wiring is inconvenient or further away, just stick the wireless sensors where you need them. The wireless sensors will operate up to 300 feet line-of-site* away from the Sensaphone 2800. Not far enough? Just add a wireless repeater to go farther. The repeater can be located up to 4000 feet line-of-site* from the 2800. Then, one or more sensors can be located up to 300 feet line-of-site* from the repeater.

Notification

Just like the other Sensaphone products, the Sensaphone 2800 uses the reliability of a standard phone line to make phone calls to the appropriate personnel to announce alarm conditions. Each monitoring condition, both wired and wireless, can have a custom voice message attached to it. Each message is recorded in your own voice for easy alarm identifi cation. Alarm notification will repeat out to eight people until acknowledged.

Applications

Use the 2800 to monitor multiple greenhouses without wires, multiple barns, coolers, freezers, or a wide variety of remote equipment. The new Sensaphone 2800 can be used anywhere you would use our other Sensaphone products. The 2800 just makes installa tion and expansion faster and easier. Extend your reach and monitor your critical remote locations with the new Sensaphone 2800.

SPECIFICATIONS

Shipping Weight 8 lbs.

Batteries 3.4Ah sealed rechargeable battery (included)

Telephone Connection FCC approved RJ-11 plug-in modular connector with 6' cord

Operating Temperature Range Unit should be kept between 32° F and 120° F

Temperature Sensing Range –109º F to 115º Fwith remote temperature sensor NRTL listed for compliance with U.L. Standard 60950-1